----------------- BitMo™ 10-uator™ (PLATE)----------------
Add-on kit (parts and instructions) for Epiphone Valve Junior, Fender Champ, Champion 600, etc.
Includes support for 4, 8 or 16 ohm confighration!
Configure for 4 ohms for use with the EVJ Combo, or for 16 ohms for use with the (highly recommended) matching EVJ extension cab.
This PLATE version mounts on the back panel of an EVJ head or combo.
This attenuator gives you control of the speaker volume so you can get great cranked tone from your Epiphone Value Junior at studio or bedroom levels. It also includes a variable level, speaker-voiced line output so you can plug directly into a mixer for recording or live performance. Better yet, you can use the whole amp as a pre-amp into a bigger guitar amp. The kit is easy to build and comes with instructions and all required parts including a pre-drilled and labeled faceplate. It requires no wiring modification to the amp. You will need an extra speaker cable. If no speaker is plugged into the output jack, a power soak resistor is switched into the circuit so you can use the amp as a preamp only.
The BitMo 10-uator is rated at 10 watts. The kit contains parts and instruction to allow configuration for 4, 8 and 16 ohm amps and speakers.
Tools you will need – screwdriver, soldering iron, solder, small allen wrench, wire stripper, needle nosed pliers. Plate requires a hot glue gun.
BitMo Mods – Features Matrix
|
BitMo Kit |
Installation &
Estimated time |
External Controls |
Circuit interface points / config options |
Works with |
|
10-uator
Box or Plate |
Easy / Novice
2 hours |
1 Speaker Attenuation knob
1 Line Out Level knob
|
None - no circuit mods to the amp
No drilling required |
EVJ amps with or without other mods |
|
Spanky |
Easy / Novice
1 hour |
None -no drilling required |
5/5 |
Tone or Brat
and 10-uator |
|
Brat |
Moderate
2 hours |
1 Tone knob w/pull boost
British voicing when pulled |
3/2 |
Spanky and
10-uator |
|
Trio |
Moderate +
3-4 hours |
1 3-way Voicing switch +
1 Tone knob w/pull boost |
7/2 |
10-uator |
*** !!! BitMo Demos !!! ***
Night of the Dogmen
This song demonstrates various BitMo mods. I re-amped the lead guitars through EVJ heads with a 12 “ ceramic Weber Blue Dog speaker miked with a Shure SM57 on the grill and a Neuman U87 room mic at about 4’. The main lead guitar parts panned near the center use the Mo’ setting of the Trio mods (similar to the Brat). The leads on the left are using a Spankified EVJ. The rhythm guitar uses the Low setting of the Trio with a Jensen speaker and Spanky through a 10-uator to a Motion Sound Leslie.
The lead guitar parts are played by Alan Magee (thanks). I wrote the song, played rhythm and bass guitar and sang. Let me know what you think. Anyone else have a BitMo demo? Send it to me. If I post it, I will send you a free Spanky or Tone Control kit.
http://demos.dovetailsystems.com/bruce/Bruce%20Hutcheon%20-%20Night%20of%20the%20Dogmen%2006.mp3
### You can get this kit pre-built for an additional $40. ###
### Add a Tweaky kit for $15, shipping included. ###
### Just add to the price when you pay and add a note. ###
On Nov-16-07 at 12:17:45 PST, seller added the following information:
See the 10-uator review at GearScore.com
http://gearscore.com/b/boxx/knowledgebase.asp?iid=137&Cat=15
On Dec-26-07 at 13:08:10 PST, seller added the following information:
The 10-uator Plate also works great with the new Blackheart Little Giant amp. It mounts on the back panel exactly the same as the Epi Valve Junior. Check out the new BitMo Triple Bypass mod kit for the Blackheart.
On Feb-09-08 at 09:21:36 PST, seller added the following information:
You can upgrade this 10-uator to handle 22 watts. Recommended if you are gigging with a hot-rodded Valve Junior or Blackheart. Add $20 more and a note with the payment stating you want the 22 watt upgrade.
Continue shopping
|
View Cart
