Shopping Cart
View Cart
Checkout
# of Item(s): 0
Total: $0.00

Search Results

Found 3 product(s) for 10-uator Kits (1-3 of 3)

10-uator Kits
BITMO 10-UATOR 23 WATT KIT - Guitar amp attenuator
BITMO 10-UATOR 23 WATT KIT - Guitar amp attenuator

-----------------  BitMo 10-uator™  23 Watt BOX or Plate----------------

 

Add-on speaker attenuator kit (parts and instructions) for Fender Princton, Deluxe, Marshall 18 watt, etc.

Includes instructions for 8 or 16 ohm configuration - can also be used with 4 ohm amps. 

 

This upgraded 23 watt external BOX version can be used with most mid-wattage amps.

This attenuator gives you control of the speaker volume so you can get great cranked tone from your amp at studio or bedroom levels.  The voicing circuit prevents tone sucking! It also includes a variable level, speaker-voiced line output so you can plug directly into a mixer for recording or live performance. Better yet, you can use the whole amp as a pre-amp into a another guitar amp.  The kit is easy to build and comes with instructions and all required parts including a labeled faceplate. It requires no wiring modification to the amp.  You will need an extra speaker cable. If no speaker is plugged into the output jack, a power soak resistor is switched into the circuit so you can safely use the amp as a preamp only.

The BitMo 10-uator is rated at 23 watts.  The kit contains parts and instruction to allow configuration for 8 or 16 ohm speakers.  

This version is also recommended if you are gigging with a hot-rodded Valve Junior or Blackheart.  There is also a Plate version that can be mounted on the back of an Epiphone Valve Junior or Blackheart BH5H - same price. If you prefer the plate version, just add a clear note with your payment. 

Tools you will need – screwdriver, soldering iron, solder, small eyeglass screwdriver, wire stripper, needle nosed pliers, drill and 3/8" bit.

 

 

 

 

BitMo Mods – Features Matrix

 

BitMo Kit

Installation &

Estimated time

External Controls

Circuit interface points / config options

Works with

10-uator

Box or Plate

Easy / Novice

2 hours

1 Speaker Attenuation knob

1 Line Out Level knob

 

None - no circuit mods to the amp

No drilling required

Low to mid wattage amps

Spanky

Easy / Novice

1 hour

None -no drilling required

5/5

Tone or Brat

and 10-uator

Brat

Moderate

2 hours

1 Tone knob w/pull boost

British voicing when pulled

3/2

Spanky and

10-uator

Trio

Moderate +

3-4 hours

1 3-way Voicing switch +

1 Tone knob w/pull boost

7/2

10-uator

 

 

 

###     You can get this kit pre-built for an additional $40.     ###

 

###         Just add to the price when you pay and add a note.           ###

Images copied from eBay: c47c_1_12_2.JPG
Price: $79.95
 
BITMO 10-UATOR Mods Kit - Epi Valve Jr.    BOX
BITMO 10-UATOR Mods Kit - Epi Valve Jr. BOX
An attenuator for a 5 watt amp ? YES! 4, 8 or 16 ohms.
Price: $59.95
 
BITMO 10-UATOR Mods Kit - Epi Valve Jr. PLATE
BITMO 10-UATOR Mods Kit - Epi Valve Jr. PLATE
An attenuator for a 5 watt amp ? YES! 4, 8 or 16 ohms.
Price: $59.95